Nanoarchitectonics to entrap living cells in silica-based systems: encapsulations with yolk–shell and sepiolite nanomaterials

• Celia Martín-Morales,
• Jorge Fernández-Méndez,
• Pilar Aranda and
• Eduardo Ruiz-Hitzky

Beilstein J. Nanotechnol. 2023, 14, 522–534, doi:10.3762/bjnano.14.43

• precursor could be cast and gelled as thin films or hollow tubular monoliths with thin walls, improving the interaction between the encapsulated cells and a liquid medium in which the material could be placed. In addition to the optimisation of the sol–gel synthesis, the conditions for yolk–shell

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• morphology for SERS measurements can be fabricated using various methods, including sol–gel synthesis [38], thermal deposition [31][32], chemical vapour deposition [42], or electrodeposition [35], which resulted in 1.2 μm high, vertically aligned nanorods of 60 nm diameter. It was observed that thermal

Microwave-induced electric discharges on metal particles for the synthesis of inorganic nanomaterials under solvent-free conditions

• Vijay Tripathi,
• Harit Kumar,
• Anubhav Agarwal and
• Leela S. Panchakarla

Beilstein J. Nanotechnol. 2020, 11, 1019–1025, doi:10.3762/bjnano.11.86

• microscopy; Introduction The synthesis of nanomaterials in short time intervals with fewer chemicals has become increasingly important in materials science. Traditional routes of synthesizing nanomaterials, including sol–gel synthesis, solvothermal synthesis, arc-discharge synthesis, or laser ablation

Advanced hybrid nanomaterials

• Andreas Taubert,
• Fabrice Leroux,
• Pierre Rabu and
• Verónica de Zea Bermudez

Beilstein J. Nanotechnol. 2019, 10, 2563–2567, doi:10.3762/bjnano.10.247

• the polyol process” [19], the synthetic process was found to be of prime importance to shape the nanoparticles and to optimize their surface/volume ratio in relation to the magnetic behavior. A one-step non-hydrolytic sol–gel synthesis of mesoporous TiO2 phosphonate hybrid materials was applied to

Nanostructured and oriented metal–organic framework films enabling extreme surface wetting properties

• Andre Mähringer,
• Julian M. Rotter and
• Dana D. Medina

Beilstein J. Nanotechnol. 2019, 10, 1994–2003, doi:10.3762/bjnano.10.196

• example, sol–gel synthesis, electrochemical deposition, anodization, electrochemical polymerization, electrospinning, plasma treatment, chemical or hydrothermal methods, vapor deposition, layer-by-layer assembly or laser ablation [19][27][28][29][30][31][32][33][34][35][36][37][38][39]. However, the

Gas sensing properties of individual SnO₂ nanowires and SnO₂ sol–gel nanocomposites

• Alexey V. Shaposhnik,
• Dmitry A. Shaposhnik,
• Sergey Yu. Turishchev,
• Olga A. Chuvenkova,
• Stanislav V. Ryabtsev,
• Alexey A. Vasiliev,
• Xavier Vilanova,
• Francisco Hernandez-Ramirez and
• Joan R. Morante

Beilstein J. Nanotechnol. 2019, 10, 1380–1390, doi:10.3762/bjnano.10.136

• selectivity to target gases. The aim of this work is the comparison of gas sensing properties of tin dioxide in the form of individual nanowires and nanopowders obtained by sol–gel synthesis. This comparison is necessary because the traditional synthesis procedures of small particle, metal oxide materials

• ; gas transport method; nanowires; quasi-one-dimensional materials; sol–gel synthesis; tin dioxide; X-ray absorption near edge structure (XANES); X-ray photoelectron spectroscopy (XPS); Introduction Semiconductor sensor functionality relies on heterogeneous catalytic chemical processes, which makes the

• formed material. Sol–gel processes comprise the synthesis of nanopowders, consisting of spherical nanoparticles, the preparation of pastes from these powders, and finally, deposition and annealing. The development of the sol–gel synthesis of small particle semiconductor materials is no longer a

Highly ordered mesoporous silica film nanocomposites containing gold nanoparticles for the catalytic reduction of 4-nitrophenol

• Mohamad Azani Jalani,
• Leny Yuliati,
• Siew Ling Lee and
• Hendrik O. Lintang

Beilstein J. Nanotechnol. 2019, 10, 1368–1379, doi:10.3762/bjnano.10.135

• external AuNPs was suggested due to the sintering effect as reported by others [29]. As the source of the AuNPs, the organic functional groups are arranged inside the silica channels using a template sol–gel synthesis of mesoporous silica with a functional surfactant [22][23][24][25]. Due to the heat

• [Au3Pz3]C10TEG/silicahex using sol–gel synthesis [Au3Pz3]C10TEG was firstly prepared as a pale-yellow sticky solid in 69% yield using a synthetic scheme as shown in Figure 1. The fabrication of mesostructured silica/gold thin film nanocomposites ([Au3Pz3]C10TEG/silicahex) was carried out using a templated

• sol–gel synthesis according to our previous synthetic protocol [25] as shown in Figure 1 with mole ratios of [Au3Pz3]C10TEG/TBOS/EtOH/HCl/H2O 1:60:504:1.2:266. Subsequently, a medium comprised of dry ethanol (61.6 mg, 1.3 mmol), deionized water (11.9 mg, 0.7 mmol) and hydrochloric acid (0.3 mg, 2.9

One-step nonhydrolytic sol–gel synthesis of mesoporous TiO₂ phosphonate hybrid materials

• Yanhui Wang,
• P. Hubert Mutin and
• Johan G. Alauzun

Beilstein J. Nanotechnol. 2019, 10, 356–362, doi:10.3762/bjnano.10.35

Characterization and influence of hydroxyapatite nanopowders on living cells

• Przemyslaw Oberbek,
• Tomasz Bolek,
• Adrian Chlanda,
• Seishiro Hirano,
• Sylwia Kusnieruk,
• Julia Rogowska-Tylman,
• Ganna Nechyporenko,
• Viktor Zinchenko,
• Wojciech Swieszkowski and
• Tomasz Puzyn

Beilstein J. Nanotechnol. 2018, 9, 3079–3094, doi:10.3762/bjnano.9.286

• manufactured using many different methods, such as hydrothermal synthesis, sol–gel synthesis, wet-chemical precipitation and microwave processing [16][17][18][19]. Many studies have shown that HAp can cause different biological responses depending on its physicochemical properties [20][21][22]. It is also

Cryochemical synthesis of ultrasmall, highly crystalline, nanostructured metal oxides and salts

• Elena A. Trusova and
• Nikolai S. Trutnev

Beilstein J. Nanotechnol. 2018, 9, 1755–1763, doi:10.3762/bjnano.9.166

• , including a modified sol–gel synthesis of the colloids and their cryogenic processing, was used in the synthesis of nickel, iron and cerium oxide nanopowders. In this case, cerium, iron and nickel nitrates were used as metal sources for the synthesis of metal-containing sols. The sol synthesis was carried

• oxide nanoparticle formation under of sol–gel synthesis in combination with cryotreatment of the sol is presented in Figure 3 using the example of the ceria nanopowder. The process under consideration involves the interaction of hydrolyzed Ce3+ ions with DMOA to form the sol intermediate, A. Then, the

Controllable one-pot synthesis of uniform colloidal TiO₂ particles in a mixed solvent solution for photocatalysis

• Jong Tae Moon,
• Seung Ki Lee and
• Ji Bong Joo

Beilstein J. Nanotechnol. 2018, 9, 1715–1727, doi:10.3762/bjnano.9.163

• well as the crystalline properties and performance enhancement of TiO2 photocatalysts calcined at different temperatures. Keywords: mixed solvent; one-pot synthesis; photocatalysts; rhodamine B degradation; sol–gel synthesis; spherical TiO2 particles; Introduction Titanium dioxide (TiO2) is a widely

• coating strategy using a mixed solvent was successfully applied for synthesizing core–shell nanostructures, to the best of our knowledge, there is no obvious report on sol–gel synthesis of uniform colloidal metal oxide particles such as TiO2 in a mixed solvent solution of ethanol–acetonitrile. In this

• and the catalyst activity can be optimized for further enhanced activity. To the best of our knowledge, this is first report on the synthesis and systemic study of uniform colloidal TiO2 particles using sol–gel synthesis in mixed solvent conditions using ethanol–acetonitrile. Results and Discussion

Nitrogen-doped carbon nanotubes coated with zinc oxide nanoparticles as sulfur encapsulator for high-performance lithium/sulfur batteries

• Yan Zhao,
• Zhengjun Liu,
• Liancheng Sun,
• Yongguang Zhang,
• Yuting Feng,
• Xin Wang,
• Indira Kurmanbayeva and
• Zhumabay Bakenov

Beilstein J. Nanotechnol. 2018, 9, 1677–1685, doi:10.3762/bjnano.9.159

• conductivity of the composite, but also facilitates the modulation of S and Li ions, buffering the volume expansion/shrinkage caused by the fast Li insertion/deletion. Experimental Preparation of ZnO@NCNT composite The ZnO@NCNT composite was synthesized by sol–gel synthesis [13][34]. In a typical synthesis

Sulfur-, nitrogen- and platinum-doped titania thin films with high catalytic efficiency under visible-light illumination

• Boštjan Žener,
• Lev Matoh,
• Giorgio Carraro,
• Bojan Miljević and
• Romana Cerc Korošec

Beilstein J. Nanotechnol. 2018, 9, 1629–1640, doi:10.3762/bjnano.9.155

• ), scanning electron microscopy (SEM), UV–vis spectroscopy and band gap measurements. Results and Discussion Titania thin films were prepared by a particulate sol–gel synthesis, using titanium tetrachloride (TiCl4) as a precursor. During the synthesis, different quantities hydrochloric or sulfuric acid were

• precursor during sol–gel synthesis and act as sol stabilizers. Consequently, the PB degradation rate for S3 is higher than any other sample synthesized with HCl (k 1 = 0.15 h−1 for S3). Samples co-doped with N and S (e.g., S3_N0.5) have shown an increased photocatalytic activity under visible-light

• observed for samples S3_N0.5+2% Pt (k1 = 0.53 h−1) and S3_N0.5+0.015M Pt (k1 = 0.55 h−1). Conclusion Nitrogen (N), sulfur (S) and platinum (Pt)-doped titania thin films were prepared by a particulate sol–gel synthesis. An organic polymer (hydroxypropyl cellulose; HPC) was added to increase the porosity of

Cyclodextrin-assisted synthesis of tailored mesoporous silica nanoparticles

• Fuat Topuz and
• Tamer Uyar

Beilstein J. Nanotechnol. 2018, 9, 693–703, doi:10.3762/bjnano.9.64

• structures were produced using a combination of CTAB surfactant, ethylene glycol solvent and NH4OH as the catalyst. MSNs were also reported in branched forms using organosilane precursors in a one-pot, CTAB-directed sol–gel synthesis [17]. For such a system, increasing the ethyl acetate concentration led to

Bright fluorescent silica-nanoparticle probes for high-resolution STED and confocal microscopy

• Isabella Tavernaro,
• Christian Cavelius,
• Henrike Peuschel and
• Annette Kraegeloh

Beilstein J. Nanotechnol. 2017, 8, 1283–1296, doi:10.3762/bjnano.8.130

• or reverse microemulsion synthesis [34]. Using the traditional sol–gel synthesis of silica particles described by Stöber et al. [35], particles are available in the size range of a few tens of nanometres up to the micrometre range. Although the Stöber method can be utilised to obtain particles with a

Investigation of the photocatalytic efficiency of tantalum alkoxy carboxylate-derived Ta₂O₅ nanoparticles in rhodamine B removal

• Subia Ambreen,
• Mohammad Danish,
• Narendra D. Pandey and
• Ashutosh Pandey

Beilstein J. Nanotechnol. 2017, 8, 604–613, doi:10.3762/bjnano.8.65

• . Tantalum alkoxides were reacted with chlorocarboxylic acids in order to lower the susceptibility hydrolysis. When these modified alkoxy carboxylates were used in the sol–gel synthesis, they yielded Ta2O5 nanoparticles of better properties than those of the alkoxide-derived Ta2O5 nanoparticles. These

• photocatalytic activity of the nanoparticles was investigated regarding the degradation of rhodamine B (RhB). Experimental All reactions before the sol–gel synthesis were carried out under strict anhydrous conditions by using Schlenk tubes and vacuum line techniques. Ta(OEt)5 and Ta(On-Bu)5 were purchased from

• Sigma-Aldrich and used as such for carrying out the reactions. Toluene was dried by standard procedures. 1H NMR and 13C NMR spectra were recorded in CDCl3 and DMSO-d6 on a Bruker Biospin ARX spectrometer with TMS as internal reference. Ta2O5 was prepared by sol–gel synthesis through hydrolysis

Functionalized TiO₂ nanoparticles by single-step hydrothermal synthesis: the role of the silane coupling agents

• Antoine R. M. Dalod,
• Lars Henriksen,
• Tor Grande and
• Mari-Ann Einarsrud

Beilstein J. Nanotechnol. 2017, 8, 304–312, doi:10.3762/bjnano.8.33

• a dark red powder was obtained for 4-tert-butylcatechol and dopamine surface functionalized samples, respectively. More recently, Gao and Cui reported a sol–gel method in which TiO2 nanoparticles functionalized with chlorinated alcohols through hydrogen bonding were produced [21]. However, sol–gel

• synthesis often leads to poorly crystalline particles [22]. Hydrothermal synthesis [23] is simple and cost efficient [24] and allows for improved crystallinity compared to sol–gel methods [22] giving improved TiO2 characteristics for applications such as photocatalysis and solar cell applications [2][25][26

Sensitive detection of hydrocarbon gases using electrochemically Pd-modified ZnO chemiresistors

• Elena Dilonardo,
• Michele Penza,
• Marco Alvisi,
• Gennaro Cassano,
• Cinzia Di Franco,
• Francesco Palmisano,
• Luisa Torsi and
• Nicola Cioffi

Beilstein J. Nanotechnol. 2017, 8, 82–90, doi:10.3762/bjnano.8.9

• contrary, high selectivity towards NO2 gas detection was obtained by using pristine ZnO chemiresistors. Experimental Sol–gel synthesis of ZnO ZnO nanostructures were prepared via a sol–gel process following the procedure reported in [45]. The subsequent washing of the obtained gel led to the complete

Microwave synthesis of high-quality and uniform 4 nm ZnFe₂O₄ nanocrystals for application in energy storage and nanomagnetics

• Christian Suchomski,
• Ben Breitung,
• Ralf Witte,
• Michael Knapp,
• Sondes Bauer,
• Tilo Baumbach,
• Christian Reitz and
• Torsten Brezesinski

Beilstein J. Nanotechnol. 2016, 7, 1350–1360, doi:10.3762/bjnano.7.126

• narrow size distribution hold promise for many applications in different areas ranging from biomedicine to electronics and energy storage. Herein, the microwave-assisted sol–gel synthesis and thorough characterization of size-monodisperse zinc ferrite nanoparticles of spherical shape is reported. X-ray

• good material characteristics, it is remarkable that the microwave-based synthetic route is simple, easily reproducible and scalable. Keywords: 1-phenylethanol route; lithium-ion battery; nanomagnetism; nanoparticles; nonaqueous sol–gel synthesis; zinc ferrite; Introduction Spinel ferrites of the

• diameter MFe2O4 (M = Fe, Co, Mn, Ni) nanoparticles has been achieved by microwave-assisted nonaqueous sol–gel synthesis using benzyl alcohol as a high-boiling solvent [22][23]. Inspired by this work, we show here that high-quality and size-monodisperse zinc ferrite (referred to as ZFO in the following

Evaluation of gas-sensing properties of ZnO nanostructures electrochemically doped with Au nanophases

• Elena Dilonardo,
• Michele Penza,
• Marco Alvisi,
• Cinzia Di Franco,
• Francesco Palmisano,
• Luisa Torsi and
• Nicola Cioffi

Beilstein J. Nanotechnol. 2016, 7, 22–31, doi:10.3762/bjnano.7.3

• Sol–gel synthesis of ZnO ZnO nanostructures were prepared through a sol–gel process. An aqueous solution of ZnCl2 (0.1 M) was heated to 60 °C for 1 h in a water-bath under continuous stirring. Ammonia solution (0.1 M) was then added drop-wise until a dense gel was formed at pH 9 [43]. The gel was

Selective porous gates made from colloidal silica nanoparticles

• Roberto Nisticò,
• Paola Avetta,
• Paola Calza,
• Debora Fabbri,
• Giuliana Magnacca and
• Dominique Scalarone

Beilstein J. Nanotechnol. 2015, 6, 2105–2112, doi:10.3762/bjnano.6.215

• were obtained, suggesting possible applications of these nanoporous films as selective gates for controlled transport of chemical species in solution. Keywords: block copolymers; coatings; colloidal nanoparticles; silica; sol–gel synthesis; Introduction The development of smart nanoporous devices for

Morphology control of zinc oxide films via polysaccharide-mediated, low temperature, chemical bath deposition

• Florian Waltz,
• Hans-Christoph Schwarz,
• Andreas M. Schneider,
• Stefanie Eiden and
• Peter Behrens

Beilstein J. Nanotechnol. 2015, 6, 799–808, doi:10.3762/bjnano.6.83

• more than 2100 publications in 2013 (Thomson Reuters, Web of Knowledge). Several methods have been used to deposit ZnO on different substrates, for example, pulsed laser deposition (PLD) [11], chemical vapor deposition (CVD) [12][13], as well as wet chemical approaches such as sol–gel synthesis [14

Mechanical properties of sol–gel derived SiO₂ nanotubes

• Boris Polyakov,
• Mikk Antsov,
• Sergei Vlassov,
• Leonid M Dorogin,
• Mikk Vahtrus,
• Roberts Zabels,
• Sven Lange and
• Rünno Lõhmus

Beilstein J. Nanotechnol. 2014, 5, 1808–1814, doi:10.3762/bjnano.5.191

• prepared by sol–gel synthesis. Dikin et al. and Ni et al. studied SiO2 nanowires (NWs) grown at high temperature with the vapor–liquid–solid method, by using resonance and the three-point bending methods, respectively [13][14]. Houmadi et al. investigated the mechanical properties of SiO2 nanotubes (NTs

• ), which were prepared by sol–gel synthesis using organic NT templates, by using three point bending [15]. The differences of the values of the Young’s modulus measured by the listed methods were approximately 40%, which can probably be attributed to peculiarities of the measurement techniques. The effect

Template-directed synthesis and characterization of microstructured ceramic Ce/ZrO₂@SiO₂ composite tubes

• Jörg J. Schneider and
• Meike Naumann

Beilstein J. Nanotechnol. 2014, 5, 1152–1159, doi:10.3762/bjnano.5.126

• -precipitation for the preparation of powders [13], impregnation [9], dip-coating [5], or hydrothermal synthesis [4], sol–gel synthesis routes have been widely employed for the preparation of CexZr1−xO2 solid solutions [14]. Pure aqueous sols or sols stabilized by the addition of organics, e.g., surfactants

Synthesis and catalytic applications of combined zeolitic/mesoporous materials

• Jarian Vernimmen,
• Vera Meynen and
• Pegie Cool

Beilstein J. Nanotechnol. 2011, 2, 785–801, doi:10.3762/bjnano.2.87

• a ligand loss of the microtemplate [83]. In this way, the nanoparticles are not able to develop into a full-grown zeolite. Instead, they form assemblies by edge-sharing (Figure 7a), similar to the case in sol–gel synthesis [155], resulting in interparticle mesoporosity. The drawback in this